WQ Suqare linear guide rails - CSB® Plastic Bearing Technology

Product properties

● Aluminum alloy material, Hard anodized surface of sliding

● Maintenance-free linear slide guides providing virtually limitless design freedom

● Lubrication-free and dirt-resistant

● Weight saving and quiet

● Simple installation, maintenance-free

● Insensitivity to dirt through dry operation

● Variable width can be fitted

WQ02H High double square guide rails

● High double square guide rails made of aluminum

● Hard anodized the sliding surface

● Standard fitting width

WQC02 Suqare guide rail carriages-TPB

● Sliding layer material: TEFPLAS® B

● Operation temperature ±200℃

● Max. continuous running speed 1.5m/s

WQ01 Single square guide rails

● Square single guide rails made of aluminum

● Hard anodized the sliding surface

● Variable width can be fitted

WQU01 Square guide rail blocks

● Fitted LIN-11Q square liners

● Maintenance-free, dry-running

● For WQ square guide rails

WQ02 Double square guide rails

● Square double guide rails made of aluminum

● Hard anodized the sliding surface

● Standard fitting width

WQC01 Suqare guide rail carriages

● Fitted LIN-11Q square liners

● Maintenance-free, dry-running

● For WQ double square guide rails

WQC02 Suqare guide rail carriages

● Fitted LIN-11Q square liners

● Mono-design and low cost

● For WQ double square guide rails

▊Eccentric forces

● Maximum 2:1 ratio

● 1x = bearing separation on same shaft

● 2x = distance from shaft to load or force

CSB-LIN®直线轴承安装法则

● CAUTION: uneven motion or even system blockage will occur if the 2:1 ratio is exceeded !

This principle is NOT load dependent! It is NOT due to edge loading. It is also NOT dependent on the driving force used! The greater the distance between the drive and guide bearings, the higher the degree of wear and required drive force.

There may be other factors that add to the braking effect, but the coefficient of friction is the main cause.

● NOTE: The Rule(2:1) is based on the static friction value of 0.25 theoretically, However, Additional lubrication can help to drop friction and extend the 2:1 ratio.

● If you have any questions on design and/or assembly, please contact our application engineers.

no products

CSB-LMS® WQ Suqare linear guide rails

Type PDF

Size 196KB

Time 10-2022

No. CSB/CAT.062E

download

988

塑料直线轴承查找器 — CSB-LIN®

CSB-LIN® Plastic Linear Bearings Finder V2.0

view tools

▊CSB-LIN® Plastic Linear Bearings Finder[V2.0] including LIN plastic linear bearings and LINP precision linear bearings. The system is based on the analysis and calculation of a large number of test data in CSB® laboratory. You can calculations bearing data by entering parameters such as bearing load, speed, temperature and position information, The system will output bearing adaptation data and min. driving force.
▊Because the system calculate and analyze based on lab data, it can't exactly meet the ractual use requirements absolutly. The system data verification has certain limitations; CSB® recommends that the bearing must be tested again to verify whether it meets the actual use requirements.
▊CSB-LIN® Plastic Linear Bearings Finder output data information is only for design reference, and can not be used as the final standard for determining the bearing material conformity, If you have any questions, please contact CSB® sales engineers.

+86-400-6633-096

Online Tools

Product News

Customer Services

CSB® More products

Precision shafts

AS: Hard anodized aluminum shaft, the best shaft for LIN linear bearings; CS: Hard-chromed steel shaft, the effective-cost shaft; ES: 304 Stainless steel shaft, the best for chemical liquid; Shaft end processing service...

Supported shafts

Compact and low high design support;

Standard design support;

3 materials shaft: Hard anodized aluminum shaft, Hardchromed steel shaft, 304 Stainless steel shaft;

WR Round linear guide rails

Aluminum alloy material, Hard anodized surface of sliding; Maintenance-free linear slide guides providing virtually limitless design freedom; Lubrication-free and dirt-resistant...

NR Small linear guide rails

Small installation height between 6 and 12 mm;

Lightweight;

Numerous carriage options – also with pretension;

Maintenance-free, self lubricating;

Lead screw drivers

Efficient and durable CSB-LMS® high helix threads;

Self-locking trapezoidal standard threads;

Maintenance-free, dry operation;

Corrosion resistant、Resistant to dirt and Low-noise;

Flexible jaw couplings

The coupling connects the drive shaft of the axis to the Motor, An elastic polymer insert in the centre of the coupling transfers the motor torque, This damping element compensates for radial and axial clearance...

HR Linear guide rails

Standard anti-wear carriages with clearance adjustment；Very suitable for high speed applications, the speed up to 10m/s；Smooth moving, Driving force is about 10% of sliding carriages...