WR Round linear guide rails - CSB® Plastic Bearing Technology

Product properties

● Aluminum alloy material, Hard anodized surface of sliding

● Maintenance-free linear slide guides providing virtually limitless design freedom

● Lubrication-free and dirt-resistant

● Weight saving and quiet

● Simple installation, maintenance-free

● Insensitivity to dirt through dry operation

● Variable width can be fitted

WR01 Single round linear guide rails

● Single guide rails made of aluminum

● Hard anodized surface

● Weight saving and no noise

● Variable width can be fitted

WR02 Double round linear guide rails

● Dual guide rails made of aluminum

● Hard anodized surface

● Weight saving and no noise

● Standard fitting width

WR02H High double round guide rails

● High dual guide rails made of aluminum, Hard anodized surface

● Hard anodized surface

● Weight saving and no noise

WR01 Stainless steel linear guides, single round rail

● Single guide rails made of stainless steel 316Ti

● Good corrosion resistance

● Resistance to dirt with LIN liners

● Variable width can be fitted

WR02 Stainless steel linear guides, double round rail

● Dual guide rails made of stainless steel 316Ti

● Good corrosion resistance

● Resistance to dirt with LIN liners

● Standard fitting width

WRU01 Round rail sliding blocks

● Fitted standard liners EPB13

● Maintenance-free, dry-running

● Fast assembly and light weight

WRU01 Stainless steel guide rail sliding blocks

● Fitted standard liners EPB13

● Housing made of stainless steel 316Ti

● Good corrosion resistance

● For WR ES single and dual guide rails

WRU01 Round rail sliding blocks, MN2

● MN2 liners for aluminum shafts

● Maintenance-free, dry-running

● Fast assembly and light weight

WRU01 Round rail sliding blocks, TPB

● Wear layer material: TEFPLAS® B

● Operation temperature ±200℃

● Max. continuous running speed 1.5m/s

● Fast assembly and light weight

WRU01-P Round rail sliding blocks

● High strength plastic housings

● Maintenance-free, dry-running

● Fast assembly and light weight

● For WR single and dual guide rails

WRU01 Round rail sliding blocks, Long design

● Assembled 2pcs standard liners EPB13

● Carrying capacity is twice that of the standard type

● Maintenance-free, dry-running

WRU02 Round rail hybrid blocks

● Rolling and sliding hybrid blocks

● Smooth moving and driving force reduced 45%

● Sliding liners material: EPB13

WRU02 Round rail hybrid blocks, Long design

● Rolling and sliding hybrid blocks

● Smooth moving and driving force reduced 45%

● Carrying capacity is twice that of the standard type

WRC01 Round guide rail carriages

● Fitted standard liners EPB13

● Maintenance-free, dry-running

● Fast assembly and light weight

WRC01 Round guide rail carriages,MN2

● MN2 liners for aluminum shafts

● Maintenance-free, dry-running

● Fast assembly and light weight

WRC01 Round guide rail carriages,TPB

● Wear layer material: TEFPLAS® B

● Operation temperature ±200℃

● Max. continuous running speed 1.5m/s

WRC01 Round guide rail carriages,CHL

● Sliding liners material: EPB13

● With locking handwheel design

● 3/8" threaded hole for camera

● Self-lubricating, maintenance-free

WRC02 Assembled hybrid carriages, HBR

● Rolling and sliding hybrid carriages

● Smooth moving and driving force reduced 45% than the standard carriages

● Sliding liners material: EPB13

● For horizontal installation of WR02 guide rails

WRC02 Assembled hybrid carriages, SOR

● Rolling and sliding hybrid carriages

● Smooth moving and driving force reduced 45% than the standard carriages

● Sliding liners material: EPB13

● For side installation of WR02 guide rails

WRC03 Round guide rail carriages

● Fitted LIN-11 standard liners

● Mono-design and low cost

● For WR double round guide rails

▊Eccentric forces

● Maximum 2:1 ratio

● 1x = bearing separation on same shaft

● 2x = distance from shaft to load or force

CSB-LIN®直线轴承安装法则

● CAUTION: uneven motion or even system blockage will occur if the 2:1 ratio is exceeded !

This principle is NOT load dependent! It is NOT due to edge loading. It is also NOT dependent on the driving force used! The greater the distance between the drive and guide bearings, the higher the degree of wear and required drive force.

There may be other factors that add to the braking effect, but the coefficient of friction is the main cause.

● NOTE: The Rule(2:1) is based on the static friction value of 0.25 theoretically, However, Additional lubrication can help to drop friction and extend the 2:1 ratio.

● If you have any questions on design and/or assembly, please contact our application engineers.

LIN-11K Plastic linear bearing liners

● Opening design sliding liners
● Self-lubricating and dust resistance
● Made of anti-wear material EPB13,MN2,EPB5

塑料直线轴承查找器 — CSB-LIN®

Linear Bearings Finder

view tools

▊CSB-LIN® Plastic Linear Bearings Finder[V2.0] including LIN plastic linear bearings and LINP precision linear bearings. The system is based on the analysis and calculation of a large number of test data in CSB® laboratory. You can calculations bearing data by entering parameters such as bearing load, speed, temperature and position information, The system will output bearing adaptation data and min. driving force.
▊Because the system calculate and analyze based on lab data, it can't exactly meet the ractual use requirements absolutly. The system data verification has certain limitations; CSB® recommends that the bearing must be tested again to verify whether it meets the actual use requirements.
▊CSB-LIN® Plastic Linear Bearings Finder output data information is only for design reference, and can not be used as the final standard for determining the bearing material conformity, If you have any questions, please contact CSB® sales engineers.

CSB-LMS®WR Round linear guide rails

Type PDF

Size 418KB

Time 03-2020

No. CSB/CAT.052

download

2040

+86-400-6633-096

Online Tools

Product News

Customer Services

CSB® More products

Precision shafts

AS: Hard anodized aluminum shaft, the best shaft for LIN linear bearings; CS: Hard-chromed steel shaft, the effective-cost shaft; ES: 304 Stainless steel shaft, the best for chemical liquid; Shaft end processing service...

Supported shafts

Compact and low high design support;

Standard design support;

3 materials shaft: Hard anodized aluminum shaft, Hardchromed steel shaft, 304 Stainless steel shaft;

NR Small linear guide rails

Small installation height between 6 and 12 mm;

Lightweight;

Numerous carriage options – also with pretension;

Maintenance-free, self lubricating;

Lead screw drivers

Efficient and durable CSB-LMS® high helix threads;

Self-locking trapezoidal standard threads;

Maintenance-free, dry operation;

Corrosion resistant、Resistant to dirt and Low-noise;

Linear drive modules

Standard design;

Various materials for shaft and lead screw;

Maintenance-free and optionally corrosion resistant;

Temperature resistant up to +60 ℃;

Motors and controllers

This motor cable directly exit from the housing, They are suitable for installation in an extra housing or for the machine equipment in cleaning the environment; Stepper motor driver is based on PID current control...

Flexible jaw couplings

The coupling connects the drive shaft of the axis to the Motor, An elastic polymer insert in the centre of the coupling transfers the motor torque, This damping element compensates for radial and axial clearance...