● Good wear resistance and with low hardness and roughness requirement for the shaft material. The wear resistance of the material will not be weekend even under the dust environment
● Continuous working temperature: -40℃/+90℃
● Maintenance-free dry operation
● Small wear off amount against various shaft materials
● Lower friction
● Low water absorption
Material properties
Standard
Unit
CSB-EPB15
General properties
Color
-
-
Yellow
Density
ISO1183
g/cm3
1.30
Max. moisture absorption, 50%RH
ISO62
%
1.3
Max. water absorption
ISO62
%
6.5
Coefficient of sliding friction(steel)
ITS025
µ
0.05-0.15
Max. PV value
ITS026
N/mm2×m/s
0.90
Mechanical properties
Flexural modulus
ISO178
MPa
4000
Flexural strength
ISO178
MPa
130
Max. static load
ITS027
MPa
70
Max. dynamic load
ITS028
MPa
35
Shore hardness
ISO868
D
79
Physical and thermal properties
Long-term application temperature
ITS029
℃
+90
Short-term application temperature
ITS029
℃
+180
Lowest application temperature
ITS029
℃
-40
Thermal conductivity
ISO22007
W/m/K
0.24
Coefficient of thermal expansion
ISO11359
K-1×10-5
8
Flammability
UL94
Class
HB
Electrical properties
Volume resistance
IEC60093
Ω·cm
>1013
Surface resistance
IEC60093
Ω
>1012
*ITS: CSB company's internal test standards. **Test temperatures are 23℃ unless otherwise stated.
The max PV value of the CSB-EPB15 plastic bearings is 0.9N/mm2×m/s which determines the load capacity of bearing is inversely proportional to the speed. Please refer to the chart for more detailed information (Graph EPB15-1).
▊ Load, speed and temperature
CSB-EPB15 allows the Max static load of 70Mpa, The max compressive deformation rate under the max load is listed in Graph EPB15-2, The actual load capacity of bearing is slightly less than 70Mpa, The bearing load is variable against the speed and temperature, Fast speed (Vmax: 1.0m/s) results into higher temperature (Tmax: 90℃) which decreases the load capacity of the bearing. Please refer to the Graph EPB15-3 for such variation.
▊ Friction factor, wear and shaft material
▊ Friction factor
Graph EPB15-4 shows that the friction factor of CSB-EPB15 is not sensitive to the operation speed and Graph EPB15-5 shows that the friction factor is CSB-EPB15 is decreased along with the loading increasing and become stable when the loading is over 20Mpa. Graph EPB15-6 tells that the friction factor of CSB-EPB15 is also not sensitive to the shaft roughness but we still recommend the shaft roughness to be Ra0.3~0.6.
CSB-EPB15
Dry
Grease
Oil
Water
Friction coef. μ
0.05~0.15
0.09
0.04
0.04
▊ Wearing and shaft material
Graph EPB15-7 shows that the wearing of CSB-EPB15 is sensitive to different materials under rotation operation with the loading of 2Mpa. It is suitable for hardened shaft, high speed steel shaft and hardened chrome steel shaft in the rotation operation. Hardened chrome steel shaft is the best choice for CSB-EPB15 (Graph EPB15-8). The wearing will be decreased as long as the loading increasing.
▊ Chemical resistance
CSB-EPB15 is good at chemical resistance against weak acidic medium and various kinds of lubricants.
▊ Water absorption
The moisture absorption of CSB-EPB15 plastic plain bearings is 1.3% in standard atmosphere. The max. water absorption is 6.5% in water. The application environment has to be considered due to the high water absorbtion properties.
▊ UV resistance
CSB-EPB15 can maintain its color unchanged when it is exposed into the UV ray. The material performance stays stable.
▊ Installation tolerances
CSB-EPB15 bushing tolerances after pressfit
Diameter [mm]
Inner diameter E10 [mm]
Housing H7 [mm]
Shaft h9 [mm]
>0～3
+0.014～+0.054
0～+0.010
0～-0.025
>3～6
+0.020～+0.068
0～+0.012
0～-0.030
>6～10
+0.025～+0.083
0～+0.015
0～-0.036
>10～18
+0.032～+0.102
0～+0.018
0～-0.043
>18～30
+0.040～+0.124
0～+0.021
0～-0.052
>30～50
+0.050～+0.150
0～+0.025
0～-0.062
>50～80
+0.060～+0.180
0～+0.030
0～-0.074
>80～120
+0.072～+0.212
0～+0.035
0～-0.087
>120～180
+0.085～+0.245
0～+0.040
0～-0.100
Medium
EPB15 bearings resistance
Alcohol
Resistant
Hydrocarbons
Resistant
Greases. oils
Resistant
Fuels
Resistant
Diluted acids
Conditionally resistant
Strong acids
Not resistant
Diluted alkalis
Resistant
Strong alkalis
Conditionally resistant
CSB® Bearing Material Chemical Resistance
Please select bearing material and medium...
R - Resistant
CR - Conditionally resistant
NR - Not resistant
ND - No test data
RD - Resistant，but the dimension changed due to moisture absorption
NO - No data
CSB® bearing material chemical resistance data is a comparison test result of the CSB chemistry laboratory using laboratory specimens or similar chemicals at room temperature 23 ℃, without considering the impact of other temperatures and chemical medium mixtures on the chemical resistance of CSB® bearing materials ; Therefore, this data can only act as a reference. CSB® recommends that the chemical resistance of actual parts should be tested under application conditions and verify the suitability of the bearings.
▊CSB-EPB® Plastic Bearings Finder[V2.1] is based on the analysis and calculation of a large number of test data in CSB® laboratory. You can calculations material data by entering parameters such as bearing load, speed, and temperature, and finally output material adaptation data. ▊Because the system calculate and analyze based on lab data, it can't exactly meet the ractual use requirements absolutly. The system data verification has certain limitations; CSB® recommends that the bearing must be tested again to verify whether it meets the actual use requirements. ▊CSB-EPB® Plastic Bearings Finder output data information is only for design reference, and can not be used as the final standard for determining the bearing material conformity, If you have any questions, please contact CSB® sales engineers.
CSB-SFP®
Semi-finished Products Finder V2.0
view tools
DURAPLAS® Semi-finished Products Finder V2.0
▊DURAPLAS® Semi-finished Products Finder[V2.0] is based on the analysis and calculation of a large number of test data in CSB® laboratory. You can calculations material data by entering parameters such as bearing load, speed, and temperature, and finally output material adaptation data. ▊Because the system calculate and analyze based on lab data, it can't exactly meet the ractual use requirements absolutly. The system data verification has certain limitations; CSB® recommends that the products must be tested again to verify whether it meets the actual use requirements. ▊DURAPLAS® Semi-finished Products Finder output data information is only for design reference, and can not be used as the final standard for determining the bearing material conformity, If you have any questions, please contact CSB® sales engineers.
Wear resistance piston ring specially developed for the pneaumatic pump industrial application. It is easier to be installed comparing with the PTFE piston ring. Standard materials available are EPB13, EPB19 and so on.
CSB® plastic wear resistance washer. Suitable for a fitting to the uncontrollable axial space in order to reduce the vabriation and noise during the operation.
Suitable for the application where the CSB® plastic clip bearing is hard to be located. The requirement of the fitting hole is not critical and the set screw could be secured without any risk of moving.
Thin-walled plastic bearing for quick installation. It is made with CSB-EPB3M material wich is flexible for dimension viriation. Alternative material CSB-EPB7 is also available for special wear resistance requirement.
The self-lubricated bearing is developed specially for the metal plate fitting. It is made with the CSB-EPB3M material which is good at shock absorbtion and wear resistance...
